hydraulic hose specification pdf

SAE 100R13 Super Tough ISO 3862-1 TYPE 4SP ISO 3862-1 TYPE 4SH Phosphate Ester Base Fluids Extreme Tough Cover SAE 100R15 Tough Cover - SAE 100R15 Super Tough - SAE 100R15 ParMax - 8,000 psi Visual Index Super Tough 4,000 psi Constant W.P. Jack Hose Hydraulic Twin Tough Hydraulic Twin Tough A-3Hose Products Division Parker Hannifin Corporation

Standards. : Meet and exceeds EN856 TYPE 4SH. SPIRAL WIRE HOSE. SPIRAL WIRE HOSE. 02. UNICAL PRODUCT CATALOGUE. HYDRAULIC HOSES 

Construction and Specifications 7 Hydraulic Hose Selection Operating Ranges 8 Features and Fittings 9 Hydraulic Hose Section A Synflex Hose Part Number Information A2–3 Low Pressure Hose A4 Hydraulic Hose 3R30 -- -- 120 1,750 103 1,500 -- -- 86 1,250 70 1,000 -- -- -- -- -- --

See the Gates Hydraulic Hose Selection Guide;. Hose Specification Pages; and/or the Additional. Temperature Limits for Gates Hydraulic Hoses Chart.

Arctic Hose High-pressure hydraulic hose used in construction, forestry, surface mining, oil and gas, waste handling, utilities and other applications where lower temperature can impact

J517_201612. This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series

Use the hose bending fixtures on the hose cutting saw in order to prevent blade binding and they will help achieve straight consistent cuts . To meet SAE and ISO standards the hose cut must be within 5° of perpendicular, on 1" hose this is less than 3/32", Figure 3 . PTFE and thermoplastic hydraulic hoses may be cut cleanly with a shear .

The use of an incompatible hydraulic fluid will deteriorate inner tube rubber W series is high pressure hose which cleared SAE standard specification.

specifications, which Bridgestone stipulates in the catalog, Bridgestone Hydraulic hose, couplings, and accessories are developed for hydraulic 

Pressure drop in psi (pounds per square inch) per 10 feet of hose (smooth bore) without fittings. Fluid specification: Specific gravity = 0.85; Viscosity = v = 20 centistokes (C.S.), (20 C.S. = 97 S.S.U.) Pressure drop values listed are typical of many petroleum based hydraulic oils at approximately +100ºF (+38ºC).

manufacturer and exporter of Multi Spiral and. Braided Hydraulic hoses to DIN, EN, SAE, ISO,. IS & BS specifications. Parker Hannifin India is committed to 

Caterpillar was the first to design and manufacture high pressure hydraulic hose known throughout the industry as XT hose. XT hose standards far exceed industry standards still today. XT hose is impulse tested to one million cycles - twice the industry requirement - at 133% of working pressure using both new and aged hose.

Bridgestone Hydraulic hose, couplings, and accessories are developed for hydraulic components. Follow each product's application and specification. Avoid hose burst, leakage, and other dangers by following important steps. This catalog shows the product specifications in the format below so you can select the

Hydraulic Fittings, Adapters, Standards & Specs. O-P. Hydraulic Equipment & ContiTech Crimp Specifications. Manual. Information in this catalog.

cal standards for hydraulic hoses define the burst pressure to be equal to or higher than 4 times the working pressure (safety factor 4). This rule and.

This hose shall consist of a thermoplastic inner tube resistant to hydraulic fluids with suitable synthetic fiber reinforcement, and a hydraulic fluid and weather resistant thermoplastic cover. Specification: Metric Size SAE Dash Size ID Min ID Max OD Max Max Working Pressure MPa Min Bend Radius 3.2 -2 3.4 4.0 9.5 21 25 5 -3 4.6 5.4 11.4 21 90

Hose Flow Capacities Pressure Drop Pressure drop in psi (pounds per square inch) per 10 feet of hose (smooth bore) without fittings. Fluid specification: Specific gravity = 0.85; Viscosity = v =

Hydraulic Industry Standard Industry standards set specific require- ments concerning construction type, size, tolerances, burst pressure, and impulse cycles. Available in either braided or spiral constructions. For use with petroleum- based fluids, diesel fuel, hot lubricating oil, air, ethylene glycol anti-freeze, and water. Transportation

Hydraulic – Industry Standard. Suction and Return. Push-Lok®. Phosphate Ester. Low Temperature. Transportation. Alternative/Marine Fuel. Refrigerant. Hose.

Hose Information—The Government Specification and the Custodian of the Specification should be consulted for infor-mation regarding the use of the hoses. 6. Internal Abrasion—For applications of a highly abrasive nature where the hose makes one or more bends, hose should be rotated 90° periodically to lengthen service life.

Inside Diameter (I.D.) • Outside Diameter (O.D.) • Reinforcement Outside Diameter • Burst Pressure: It is the minimum guaranteed burst pressure of the hose; equivalent or superior to the reference specifications minimum requirements. • Weight • Maximum Working Pressure • Minimum Bend Radius • Ferrule/Socket

Bridgestone offers superior performance hoses which exceed SAE/DIN test requirements. Examples of EPOQU series hoses are shown below. 15% 5% Test pressure ±5% 1.0MPa 0MPa

Constant Pressure - Made to ISO 18752 specifications, and YKR2SN - 2SN/R2AT 2-WIRE YOKOHAMA PREMIUM HYDRAULIC HOSE. FOR MEDIUM AND HIGH PRESSURE LINES 

Type 'S' & GC / VA hose available in length of 250, 300, 400, 500, 600, 750, 1000, 1250, 1500, 1750, 2000, 2250, 2500, 3000, 4000 & 5000 mm ex-stock. Required length can be made. ACCESSOEIRS All the accessories are available in BSP / METRIC / JIC threads made from Mild Steel, Brass or Stainless Steel materials.

Construction and Specifications 7 Hydraulic Hose Selection Operating Ranges 8 Features and Fittings 9 Hydraulic Hose Section A Synflex Hose Part Number Information A2-3 Low Pressure Hose A4 Hydraulic Hose 3R30 -- -- 120 1,750 103 1,500 -- -- 86 1,250 70 1,000 -- -- -- -- -- --

Refer to SAE J517 for specifications of hose and information on hose assemblies. Reinforcement: 2 high-tensile steel wire braids. Selection The following is a list of factors SPEC